JustEnoughDucks

In Belgium, we are forced by law to use Cca data cables because of "lower fire risk" while I hear literally everywhere that CCA data cables have a much higher fire risk.

Everything here has to comply with the euroclass chart level cca or higher which is confusing because they seem to be combustibility(ca) ABCDEF rating. Making the minimum required in Belgium (and the most prevalent) Cca.

I think for example that getting this for PoE (sorry, in Dutch) would be fine because it does say that it is pure copper, but it also says that it is CCA which is confusing.

Not really a question or anything, just very confusing considering Cca and Eca are the 2 cable types used for residential homes which happen to correspond also to Copper clad aluminum and Enhanced Circuit Integrity. Adds extra probably completely unnecessary stress.

Hey everyone,

I am completely stripping my house and am currently thinking about how to set up the home network.

This is my usecase:

• home server that can access the internet + homeassistant that can access IoT devices

• KNX that I want to have access to home assistant and vice versa

• IoT devices over WiFi (maybe thread in the future) that are the vast majority homemade via ESPHome. I want them to be able to access the server and the other way around. (Sending data updates and in the future, sending voice commands)

• 3 PoE cameras through a PoE 4 port switch

• a Chromecast & nintendo switch that need internet access

Every router worth anything already has a guest network, so I don't see much value in separating out a VLAN in a home use case.

My IoT devices work locally, not through the cloud. I want them to work functionally flawless with Home assistant, especially anything on battery so it doesn't kill its battery retrying until home assistant polls.

The PoE cameras can easily have their internet access blocked on most routers via parental controls or similar and I want them to be able to send data to the on-server NVR

I already have PiHole blocking most phone homes from the chromecast or guest devices.

So far it seems like a VLAN is not too useful for me because I would want bidirectional access to the server which in turn should have access from the LAN and WiFi. And vice versa.

Maybe I am not thinking of the access control capability of VLANs correctly (I am thinking in terms of port based iptables: port X has only incoming+established and no outgoing for example).

I figure if my network is already penetrated, it would most likely be via the WiFi or internet so the attack vector seems to not protect from much in my specific use case.

Am I completely wrong on this?

I got immich with SSO up and running. It runs like a dream compared to Photoprism and is simple enough for me, but also has necessary features like user accounts.

There is one thing I couldn't find in the docs:

I already have a library of 5000 photos and 150 videos on my server that sync to my phone with Syncthing to 4 different directories (one for each phone I took the photos on) in Immich. Right now I have that directory as an external library, but I don't think this is the "right way."

My goal:

• No duplicates between phone app and desktop app
• Don't have to re-upload every image from my phone as my network is 100/30 mbps
• Am able to manage my photos from the Immich app and web app (deleting photos that will propagate between devices)

Can I just map the "Upload" folder to that syncthing photo base folder and get parity between my phone and my server? Or do I have to re-upload everything from my phone? Or am I waiting for a feature that doesn't quite exist yet? I noticed some feature discussions about photo hashing and de-duplication.

I tried asking in a discussion on the repo, but nobody answers those much.

Hey everyone!

We are renovating our atelier to be a temporary house while we completely strip and redo the main house for a few years.

One thing I am really struggling with is how to make a large 255cm x 65cm dirty concreate workbench into a kitchen countertop for 2 years or so.

We are based in Belgium, so wood prices are about 2x what they are in the US (250cm x 125cm OSB board is 50€ or so).

The height is already quite high for a countertop (for me and my girlfriend it is perfect) so adding a thick slab of butcher block or something would make it unusable.

I don't really know what my options are. Maybe a wood veneer? Some sort of cheap-ish tile?

We used some iron-on white to finish the edge of our custom sink cabinet made from some old office cupboards, maybe there are larger ones like that that would work for concrete?

We are trying to stay below 2cm thickness. Idealy 0.5cm or so, but that would be difficult.

If anyone has any ideas to throw out, we would be open to it! It is just temporary, so it doesn't have to last more than a few years

Thanks!

Edit: I realized I didn't have any good pictures of the bench itself since it always took a back seat, but here are a few bad ones to give an idea from in the beginning https://imgur.com/a/KgiqHrC

I have been upgrading after a few weeks of being too busy too. I constantly now run out of space on my 50GB root partition even when running -Sc after every update and reboot to make sure everything works...

It really is crazy that there is no option to put all the programs on another partition than root unless you make a separate partition for /usr that will somehow foresee what you will install in the future.

My /usr with all of my programs installed is 29GB and /var takes up 10 GB. That leaves just 10GB for everything else.

I have just followed the partitioning advice since my first 2016 install, but in the past few years, everything has just ballooned in size it seems and is now always a problem every few years no matter how big you make your root partition.

Is there a better solution for this? Can we place /usr files managed through managers in /home? I think that is against the pacman/yay way of working.

It's weird. I have been working from the office 5 days a week instead of the normal 2-3 days for a few months.

Now I only get to have my nice V60 coffee on the weekends because my 1 hour to 1h15 commute time takes up too much time.

I end up using the work coffee machine, which does grind whole beans for my coffee at work. It is very inconsistant. The same setting often gives either watery coffee or overextracted coffee depending on how it feels that minute.

It has made me really enjoy and savor my weekend coffee much more than when I was having good coffee every day. Like the contrast made me realize how good it already was without chasing a better grinder/better water/better methods.

Does anyone else have this sort of experience?

Hey lemmings,

I have a headless server that works beautifully. B450 with 2700X and 32GB of micron 3200MHz RAM.

I am currently running Debian 12 Bookworm on it. I am at kernel 6.1, but in preparation for 6.2 or 6.3 being backlogged, I want to buy an Arc A380 for transcoding since they are only 150€ here. Software was fine for a single video stream, but I bought a new house and will have 4 camera streams running. Plus I want to dabble in AV1 transcoding for media or storage of my camera streams

Currently there is neither X nor Wayland installed since it is exclusively with SSH that I do all of my work on it. After I install the GPU, I was wondering if it is possible to not even install X or Wayland since I will literally never use a display on it?

Would I still be able to do Jellyfin and Frigate transcoding without an X server? If I have to get one, does it matter if I choose X or Wayland for hardware transcoding?

Thanks!