darkmarx

Historically, this is exactly how theological disputes were handled. See Crusades on Wikipedia for more information.

If you're getting water inside, Jchannel is probably the least of your concerns. Something isn't sealed correctly. Unfortunately, if you have water getting in, you have water in your wall. Even if you seal the window, you could end up with a mold issue.

If it was me, I'd pull the window, ensure all flashing and housewrap is in place, the reseat the window in a thick bead of silicone. Assuming the window is still in good shape. Otherwise, a new window is needed. Once the window is in place, trim, jchannel, and siding would be put back.

Once the window is properly installed, I'd focus on the inside. Pull the trim and drywall around the window, letting it air out for a day then coat the inside sheeting with mold killing primer. New insulation would be added before new drywall is put in. Then mud, sand, paint, and reinstall the trim.

It's a decent amount of work, but not insurmountable. My concern is, if it was installed incorrectly, chances are, your other windows were too. I'm not trying to be doom and gloom here, just trying to forewarn you. It's something to keep an eye on.

All of this is assuming the problem isn't something like a window left open or something like that.

Thanks Sata . . . What the fuck is wrong with you? Who hurt you? You will live rent free in my head for a long time. Just so you know, I hate you for that. You magnificent bastard, you. Bravo. Bra fucking vo. 👏👏

The silver things are runners with ball bearings that drawer slides on. The slides that attach to the drawer will snap into these silver runners.

Usually, you just need to align the slides on the drawer with the runners and push. They should snap in. The runners tend to slide around while connecting them. If they slide to the back, it's ok, they will still connect once you get them lined up and push the drawer into them. If you can reach from underneath, you can hold the runner in place while attaching the drawer. Do one side at a time.

If you're struggling to get it to connect, I recommend removing the slide from the side of the drawer and seeing if you can get a single slide to attach to the runner. It will click when it attaches. By doing just one, you might have an easier time seeing how it connects.

Once you figure it out, you'll need to disconnect it. There should be a little plastic lever that you hold down (or up, depending on the side) while you pull out the slide. Put it back on the drawer and see if you can connect it once it's back on the drawer.

They are a little complicated, but once you see how it goes together, it should make sense. If what I said is still confusing or if you are still struggling, reply and I'll see if I can get some pictures to explain it better.

• Edit: A common mistake I've seen is putting the slides on the drawer backwards. The part attached to the drawer should have the flat part against the drawer. The drawer should look like this ]|_______|[

I'm in the middle of a livingroom remodel. This weekend, the plan is to fix the leak in the roof, rebuild thr staircase to match modern codes, and install the new hvac ducts. If time permits, I'd like to start hanging drywall, but I know thats a stretch. I want to get the room done by the 4th, and I'm not sure if I'll make it.

I think I get where you are coming from here, though I question the certainty in it. There is too much nuance to humanity to never trust or always ignore.

If you never anticipate good in others, you must be very lonely - never trusting, always defensive, waiting for the next attack. We all have different levels of trust shaped by our own experiences. Personally, I try to anticipate good until a person proves otherwise. I'd rather be disappointed occasionally than miss a possible connection to someone because I never anticipated goodness.

As far as receiving advice, take it from anyone and everyone. We constantly do this, even if we don't notice. We take in the world around us. We decided if it was good, bad, or somewhere in between. If I see someone hit their thumb with a hammer, I learn not to hold the nail in the way way did. It's non-verbal, yet in its own way, is advice. Verbal advice works similarly. Take it in, listen to it, accept or reject it. Ether way, it is part of you. You will adapt it to your own view. If someone says that jumping of a bridge is the best thing ever, you can ignore them or you can do it. Ignoring them shapes a picture of that person as irresponsible or dangerous while shaping you to be more conscious and risk-averse. Doing it shapes that person in your mind as someone to listen to in order to do something fun. I suppose what I'm getting at is a simple question, can you really ignore advice?

I'm probably just thinking more into it than you intended.

Good luck to you. Post the results when you finish. I'm sure more than just me would like to see it

Shellac is not the same as oil based. Oil based is made from, well, oil. Shelllac is made by crushing the shells of the lac bug. It is an insect that is cultivated specifically for the purpose. Shellac is typically used as a final coat for protection. Shellac primer is basically that mixed with a white pigment. It is great for sealing. Fairly pricy though.

I will echo the Bondo route that others suggested. The big box hardware stores sell quart cans of general purpose Bondo in the paint aisle.

Cut out the vaneer over the bad area with a razor blade or box cutter.

Sand with 80 or 120 grit to remove any loose bits of the board. The particle board will crumble a little, but it will be fine. Just dont go overboard. Vacuum it to remove most dust.

Using a flexible putty knife, get one to two globs of Bondo on a clean piece of cardboard. Don't do too much as you will have about 5 minutes of working time once the hardener is added. Follow the instructions on how much hardener to add, you wont need much. Fold the hardener into the Bondo with the putty knife until it is a uniform color.

Spread the bondo over the area you cut out. Try to get it smooth, but dont overwork it. It doesn't have to be perfect.

Using 60 or 80 grit paper, sand it as it starts to dry. If it is gumming up the paper, it is still too wet to sand, give it another minute or two and try again. You are shaping it with this step. If you let it completely dry, it is hard as a rock and more difficult to sand.

Once it is in a good shape, switch to the next step up for sanding and repeat (60 to 80 to 120 to 180 to 220). Do not skip gits or you will just make work for yourself. You can probably stop at 180, but since it is next to vaneer, i'd go to 220. Again, if it is gumming the paper, wait a few minutes. Once you are at 220, use it to sand the entire cabinet to rough up the surface and accept primer better.

Once sanded, wipe the entire cabinet down with a tac cloth. I also recommend wiping the cabinets with a wax and greese remover so everything will stick better.

Now it is time for primer and paint. For a smooth finish, use a good quality foam mini-roller and foam brush for tighter areas.

Prime the cabinet using any water-based primer; killz is pretty good. They make an oil based that would be better, but will smell up your whole house, so I don't recommend it unless you have excellent ventilation.

Lightly sand the peimer once it is fully dried with 220. If any spot is too light, do a second coat. Wipe up the dust.

Paint with an alkyd paint. Do at least 2 coats.

Not necessary, but if you want extra protection, you could use a foam brush (not a roller here) and do 3 to 4 coats of a water-based polyurethane on top of the paint. It might be overkill for what you want though.

This might seem like a lot, but you will have a great finish when done. Also, fair warning, Bondo has a strong smell. Open a window.

In general, If I need to cut off more than its capacity, I'm using a circular saw with a track or straight edge.

As for the price, I wasn't aware it was so high. I paid $350 for it. I think it was a holiday sale or something like that.

It wasn't $500 when I got it. I think it was $350 at the time. Although it might have just been on sale.

amzn.com/dp/B0BN1XB7LK

This is the one I have. I take the batteries out of it after each use, otherwise it drains it. That's my only complaint with it.