this post was submitted on 28 Feb 2024
79 points (96.5% liked)

3DPrinting

15657 readers
146 users here now

3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.

The r/functionalprint community is now located at: !functionalprint@kbin.social or !functionalprint@fedia.io

There are CAD communities available at: !cad@lemmy.world or !freecad@lemmy.ml

Rules

If you need an easy way to host pictures, https://catbox.moe/ may be an option. Be ethical about what you post and donate if you are able or use this a lot. It is just an individual hosting content, not a company. The image embedding syntax for Lemmy is ![](URL)

Moderation policy: Light, mostly invisible

founded 2 years ago
MODERATORS
andypiper@lemmy.world
henry_rowengartner@lemmy.world
j4k3@lemmy.world
GrayBackgroundMusic@lemm.ee
79
How do I fix these god-awful seams? (sopuli.xyz)
submitted 9 months ago by DreadPotato@sopuli.xyz to c/3dprinting@lemmy.world
71 comments fedilink hide all child comments
 

I have trouble fixing the terrible seams I'm getting. I've followed Elli's print tuning guide and calibrated extruder, tuned PA (it's now 0.035) and extrusion multiplier.

I've tried adjusting both retraction length and speed, but it doesn't seem to have much impact. I'm not using "wipe on retract" or "retract on layer change", I only retract if travel distance is longer than 3mm. Retract is 0.3mm @35mm/s.

I've tried reducing PA smooth time too, but this also doesn't seem to have a noticable impact.

I've tried reducing seam gap from the default 10% in Orca all the way down to 0%, but the bad seams persist.

I've tried with "wipe on loops" both disabled and enabled with no difference.

I've tried with both arachne and classic wall generator, no difference.

I've tried different wall orders, inner/outer, inner/outer/inner and outer/inner, all with the same bad seams.

Filament in the picture is matte PLA, it is without doubt dry and generally prints well aside from the seams. It's stored vacuum sealed with silica, and I use a filament dryer to dry if I suspect wet filament.

I'm running out of ideas for where to tweak to get a decent result.

(page 2) 22 comments
sorted by: hot top controversial new old
[–] maxwellfire@lemmy.world 2 points 9 months ago* (last edited 9 months ago) (1 children)

Is the bad side of the seam where it stops or where it starts printing the outer wall? I assume it's where it stops and then it cross the wall to form the infill?

To add to the PA questions, are you sure that your PA setting actually are changing anything?

What printer is this and what firmware?

Does a spiral mode print work fine?

What if you print the part significantly slower (to rule out rigidity/acceleration issues)

[–] DreadPotato@sopuli.xyz 1 points 9 months ago

Is the bad side of the seam where it stops or where it starts printing the outer wall? I assume it's where it stops and then it cross the wall to form the infill?

Correct, but this still happens when printing without infill, although less.

To add to the PA questions, are you sure that your PA setting actually are changing anything?

When printing the PA pattern, I can clearly see a difference. I haven't seen a huge difference in the actual print quality. It doesn't seem to have the any effect on this issue.

What printer is this and what firmware?

It's an anycubic kobra 2 bedslinger running klipper

What if you print the part significantly slower (to rule out rigidity/acceleration issues)

Tried printing at both 30mm/s and 100mm/s, it looks the same aside from slightly worse ringing at the higher speed.

[–] Mpatch@lemmy.world 1 points 9 months ago* (last edited 9 months ago) (1 children)

What printer do you use. This is a mechanical issue. It's something binding as the one x or y is traveling could be a bearing or the stepper motor it self. It prevents the arc from being fully formed even though the machine thinks it is key point you made is that randomized z seam leaves the same mess, but if notice it's not all the layers are cut short only some.

Take the belt off and move the axis by hand slow and easy do you feel anything that isn't smooth like silk? That would be it. Feel the stepper is the drive gear tight any slip ?? Any play in the shaft side?

Edit

Looking at the pictures again I'd bet that if you went taller and printed faster, it would be even worse because the bad part got hotter and more bound up more Alternatively printing faster might make it better because you have the inertia to push past the binding spot.

[–] DreadPotato@sopuli.xyz 1 points 9 months ago* (last edited 9 months ago) (1 children)

It's an anycubic kobra 2 running klipper.

Randomized seams leaves the same mess, but randomly distributed around the model and not aligned like in the picture. But each seam is equally bad everywhere on the model.

Speed doesn't seem to affect the issue, I've tried both 30mm/s and 100mm/s

I disassembled the X and Y axes yesterday to check the motion system, moving by hand seems as smooth as it's ever been, no slip that I could feel. I think one roller on the X axis is very slightly oval unfortunately, but moving the model to different locations have no effect on this, and rotating models so seams align differently on the axes doesn't change anything, so I don't think that's the source of the issue.

[–] Mpatch@lemmy.world 1 points 9 months ago (1 children)

Can you post the g code ?

[–] DreadPotato@sopuli.xyz 1 points 9 months ago

I'll post it later today

[–] Anticorp@lemmy.world 1 points 1 month ago

Change z-seam to random in Cura.

[–] tagginator@utter.online -2 points 9 months ago

New Lemmy Post: How do I fix these god-awful seams? (https://lemmy.world/post/12523802)
Tagging: #3dprinting

(Replying in the OP of this thread (NOT THIS BOT!) will appear as a comment in the lemmy discussion.)

I am a FOSS bot. Check my README: https://github.com/db0/lemmy-tagginator/blob/main/README.md

load more comments
view more: ‹ prev next ›