this post was submitted on 06 Apr 2024
196 points (95.0% liked)

Coffee

8422 readers
86 users here now

☕ - The hot beverage that powers the world!

Coffee gadgets - It's always great to learn about new gadgets. Please share your favorite hardware or full setups. It might inspire newcomers to experiment!

Local businesses - Please promote your local businesses. If you are not the owner of the business you are promoting, kindly ask the owner if it's okay. It would be great if the business has a physical store to include an exterior or interior shot.

founded 1 year ago
MODERATORS
martijn@lemmy.world
dannoffs@lemmy.sdf.org
Xariphon@kbin.social
196
How do you guys grind your coffee? (media.kbin.social)
submitted 7 months ago by shininghero@kbin.social to c/coffee@lemmy.world
75 comments fedilink hide all child comments
 

I just retrofitted my basic hand crank mill with a 10mm nut, and drove it with a drill. It's so much faster now, but I do wonder if there's actual properly motorized versions of what I just did.

you are viewing a single comment's thread
view the rest of the comments
[–] Deez@lemm.ee 2 points 7 months ago (7 children)

I’m using a Breville Smart Grinder Pro that I modified to be single dose. I just ordered a DF64 Gen 2, but it hasn’t arrived yet.

[–] hamburgers@lemmy.world 2 points 7 months ago (1 children)

Enjoy the DF64 😃

[–] Deez@lemm.ee 1 points 7 months ago (1 children)

Thanks, I’m looking forward to it! But also a little nervous that I won’t be able to tell the difference. 😅

[–] hamburgers@lemmy.world 1 points 7 months ago* (last edited 7 months ago) (1 children)

It's a flat burr grinder, you definitely will. Do you know about aligning it or whatever?

[–] Deez@lemm.ee 1 points 7 months ago (1 children)

The vendor (df64coffee.com) say they align the burrs. Would they need further alignment?

[–] hamburgers@lemmy.world 1 points 7 months ago* (last edited 7 months ago) (1 children)

They should be aligned then, but it could be tested with the dry-erase marker test. I will link the process, butI want to give you some general need to knows.

For reference, I have the first Gen one.

  1. Whenever you remove the adjuster top. (The thing you turn to adjust the grind. When you loosen it all the way.)

a. Use a dry-erase marker and mark somewhere on the top burr section so you can put it exactly the way it was. (Before you lift it up). Not marking it is a good way to mess with alignment because it is only aligned one specific orientation.

b. The threads are very fine. So make sure to be careful not to crossthread them when you screw it back on. Whether you are removing it to clean or whatever.

  1. You will want to zero out the grinder. To do this, first thing before you put grounds in. Or when it is completely cleaned out. With the power off and unplugged, tighten the adjuster gently until the burrs touch. You tighten and turn the burrs by hand, I believe clockwise, keep doing it until you hear and feel that the burrs are touching. Then take the grinder setting pointer thing and orient it where zero is.

This is the marker test: https://youtu.be/mIugzsjzEUI

[–] Deez@lemm.ee 1 points 7 months ago (1 children)

Thanks very much for that, I really appreciate it! How have you found your DF64?

[–] hamburgers@lemmy.world 2 points 7 months ago

I absolutely love it. I also have a comandante C40 but cups from the DF64 are better.

load more comments (5 replies)